Archive | Costumery RSS feed for this section

Latex and Spike Crown Tutorial

7 Feb

This is one I’ve been wanting to do for a while, but the shoot I’m going to use this for has been rescheduled several times and it seemed like a better idea to wait. I got impatient last week and decided to just go ahead and make it anyway – and, of course, to make a tutorial to show you how to make your own!

What you’ll need:

  • latex (0.8 mm to 1.2mm – I chose 1.2mm as I used fairly large and heavy spikes)
  • rubber cement
  • rubber cement thinner
  • spikes (size depends on the look you are going for)
  • fabric hole punch
  • gel pen (silver or gold work well – see extra tips below for more info)
  • ruler
  • measuring tape
  • rotary cutter

Time from start to finish: About 30 minutes.

Step 1:

So the first thing you need to do is cut your latex to the size you need. Take a measurement of your head around where you’d like the crown to sit, and then decide how wide you’d like it to be. My strip of rubber ended up being 20 inches long and an inch wide. (*If you’ve never worked with latex before, there are several places you can buy it from online and I will eventually write a post with the basics of working with latex. Until then, ask whatever you need to know in the comments!)

Step 2:

When your latex is cut to the proper size and length, mark out where you want your spikes to go. I spaced mine 1 inch apart. Use a gel pen to mark where your holes need to go. BEFORE you punch your holes, place your spikes on the marks to see if you like the arrangement – that way you can change it if it doesn’t look right.

Arranging Spikes

Checking the arrangement before punching holes.

Step 3:

Punch your holes! The punch I used was just a cheap one from the fabric section of my local Wal-Mart.

Notice the faint silver dot on the latex? That's where my holes are going.

Notice the faint silver dot on the latex? That’s where my holes are going.

Step 4:

Insert your spikes and screw them tight together – you don’t want them falling off while you’re wearing it. This may require a flat head screwdriver, but mine were all tightened by hand.

Adding my spikes! :)

Adding my spikes! 🙂

Step 5:

Now that your spikes are all in, all that’s left is gluing the two ends together. (I glued the ends first and then added spikes, but I found it would have been easier to do it the other way around.) When you do this, remember to only put glue on the front of one end and the back of the other. If you need a guide, hold the two ends together before you add glue and mark each with your gel pen to you know where to glue. To apply the rubber cement to your latex, make sure to clean it first with the rubber cement cleaner, and then use a small paintbrush or Q-Tip.

DO NOT put the two ends together yet. Wait for at least 5 minutes to let the glue ‘set’, then push the glued ends together and press firmly. If you want to make it even more secure, you can even put a spike through the glued seam after it has fully set between 12 and 24 hours later.

Latex and Spike Crown

And now you’re done! Well, you will be when your glue sets.

Extra tips:

  •  Only use rubber cement to glue the latex together. Other glues will not hold, but rubber cement is meant for this and will create a permanent hold.
  • Most suppliers only sell latex by the yard or meter. Thick latex like the stuff I used for my crown is pretty pricy (at about $35-40 per yard), but you can buy thinner latex in pre-cut strips from Sheet Latex International. The thinner latex won’t hold the heavy spikes, but you can laminate two or more layers together to create your desired weight or thickness. This will save you a lot of money if you don’t need a full yard of the heavy stuff.
  • If you decide to use a different colour (instead of the basic black I used), try to choose a dark one. Latex stains really easily, and white, pink, and other pale shades and colours will discolour from contact with the metal. These stains are permanent.
  • Gel pens – They won’t stain the latex, they wash off with a quick wipe of rubber cement thinner, and they’re cheap. Normal ball-point pens will not wash off, and neither will a lot of other writing utensils. Just go with gel pens to save yourself the trouble. (My suggestion of silver or gold is just my personal preference, but I’ve used other colours and they work just as well.)
  • Try to use spikes with 2 pieces – the spike and the screw base. They are generally higher quality and will not tear the latex.

DIY Felt and Button Crown

28 Nov

Alright, so first official blog post! This one will be fairly short as I didn’t take any photos of the process. (I’ll make up for it, I promise!) This was something I did last week to use as a prop for a family portrait photo shoot I did for some clients. It was super easy to do, although it did take some time and patience. And, if I do say so myself, I think it turned out pretty cute!

What you’ll need:

  • felt fabric (cut into strips between 3 and 5 inches wide – depending on how tall you want your crown)
  • buttons (any will do)
  • needle
  • thread (to match your felt)
  • scissors
  • fabric square (or a book corner or anything else with a nice square corner)
  • marker, pen, writing utensil in general

Time from start to finish: About 3 hours, but I spent most of that time beading the lower edge.

Step 1:

Cut your felt into strips of your desired width. Make sure it’s also long enough to wrap around your head. For mine, I had to sew two lengths together to make it long enough.

Step 2:

Layer up your felt. You can glue it together, or use double sided tape, even, to keep the pieces in place. You will want two pieces of felt sandwiched together for more structure – one layer is a bit too flimsy to keep its shape.

Step 3:

Trace triangles along the top of the strips with your marker using your square (or book) as a guide. Try to make the triangles match up from one side to the other. This will make it easier when you sew the ends together. When you’re done tracing, cut along the lines.

Step 4:

The next thing you will need to do (if you haven’t glued the felt layers together) is sew along the bottom of the strips to keep the inside and outside layers from coming apart. You can also sew along the top edges as well, although I chose not to. I hand sewed mine, but if you have a sewing machine, it will go a lot faster.

Step 5:

Start decorating! I used buttons and glass beads to decorate mine, but you can use pretty much anything – rhinestones, feathers, ribbon, cut-out felt shapes, sparkle glue, seashells, etc. The possibilities really are endless.

If you’ve used this tutorial to create your very own felt crown, I’d love to see photos! Feel free to send me the results of your adventure.